Eiechip Digital Multimeter 100V 10A

 https://www.amazon.com/gp/product/B079L33VG2

Includes unit and two cable harnesses

From the description:

  • Display Voltage and current simultaneously in different colors, red for Voltage, Blue for current (the current is Measured in the negative rail). 2 Require external power supply; with reversed connection protection. 3 Ground wire of testing end and power supply terminal is the same wire; quick refresh of about 500 MS/time. 4 With built-in shunt, has Voltage and current calibration potentiometers.

  1. 48 x 29 x 21 mm, wide measuring range(dc 0-100v; 0-10A) and high accuracy percent (± 1 digit).

Features:

  • Operating voltage:DC 4.5 ~ 30V
  • Measure voltage: DC 0 ~ 100V
  • Minimum resolution(V): 0.1V
  • Minimum resolution(A): 0.01A
  • Operating current: <20mA
  • Display: three 0.28" LED digital tube
  • Display color: Red and Blue (two-color display)
  • Dimensions: 48 x 29 x 21mm
  • Mounting cutout: 45.5 x 26.5mm
  • Refresh rate: about 500mS / times
  • Measure accuracy: 1%
  • Operating temperature: -10 to 65ºc
  • Operating Humidity: 10 to 80% (non-condensing)
  • Working pressure: 80 to 106 kPa
  • Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement

Wiring:

  • Black line (thin): vacant or buck circuit (module) negative
  • Red line (thin): power supply+
  • Black line (thick): COM, common measuring
  • Red line (thick): PW+, measuring terminal voltage input positive
  • Yellow line (thick): IN+, current input+
  • (Please refer to the wiring diagrams for more details)

Notice:

  • The voltage between the thin red and thin black
  • lines must be within DC 4.5-30V
  • The ammeter can only be connected to the negative of the device under test
  • 10A below ammeter (include 10A), built-in shunt, does not require external shunt
  • When the black thin line vacant, it is better to use insulating tape around the exposed part of the wire, to prevent short circuits
  • If just be used as a voltmeter, it is recommended that the yellow line and the black line were connected together, to prevent the ammeter digital flashing

Package include:

  • 1x Digital Volt Ampere Meter
  • 2Pcs x Cable













Comments

Post a Comment

Popular posts from this blog

nanoCH32V203 Dev Board

Image
These are all purchase variations of this page.  The chip is the new 10 cent RISC-V.  https://www.tindie.com/products/johnnywu/nanoch32v203-development-board/ https://www.tindie.com/products/johnnywu/wch-linke-debugger/ nanoCH32V203 Development Board WCH RISC-V Dual TYPE-C USB Interface LCD Interface SD Card Slot Open Source nanoCH32V203 is a development board made by MuseLab based on CH32V203C8T6 of QinHeng. It features dual TYPE-C USB interfaces, LCD interface and SD card slot on board, and can be programmed through the USB port which is convenient for prototype verification and development. Dual USB interface, USB1 supports Device, USB2 supports Host/Device Can be downloaded directly via USB without additional downloader Onboard 8MHz and 32.768K crystal oscillator FPC-12P cable connector, which can support common LCD (such as ili9341, st7789, etc.) SD card slot, which supports SD card reading and writing (SPI protoc ol) Kit 3: nanoCH32V203 Development Board x 1 + 20 Pin Hea...
Read more

ESP-M3 Mini

Image
 https://www.aliexpress.us/item/2251832658774277.html Long-range Ultra-low Mini Ultra-Small ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266 ESP8285 = ESP8266 + 1M Flash, so that it can withstand high temperatures up to 125 degrees Celsius! And the original ESP8266 source code program can be used to transplant. ESP-M3 module core processor using cost-effective chip ESP8285. The chip integrates the enhanced version of the Tensilica's L106 Diamond 32-bit core processor with on-chip SRAM in a smaller package. ESP8285 has a complete Wi-Fi network function, both can be used independently, can also be used as a slave from other host MCU running. When the ESP8285 hosting application, can be started directly from the external Flash. Built-in cache memory facilitates system performance and optimizes storage systems. In addition, ESP8285 only through the SPI / SDIO interface or I2C / UART port can be used as a Wi-Fi adapter, applied to any microcontr...
Read more