NodeMcu Lua WiFi Internet Things Amica V2 Development Board ESP8266-12E CP2102

NodeMcu Lua WiFi Internet Things Amica V2 Development Board ESP8266-12E CP2102 | eBay



Overview

The NodeMcu is an open-source firmware and development kit that helps you to prototype your IOT product within a few Lua script lines.The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Power your developement in the fastest way combinating with NodeMCU Firmware.

Open-source, Interactive, Programmable, Low cost, Simple, Smart, Wi-Fi enabled. Code like arduino, but interactively in Lua script. Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.

This is Amica V2 Version.The V2 fixes the short comings of the initial board, it’s more narrow and fits nicely into bread boards. The chip was upgraded from an ESP-12 to an ESP-12E.


Description:

  • Amica Version V2.
  • Use CP2102 instead of CH340G. Breadboard friendly.
  • Upgraded from a ESP8266-12 to a newer enhanced ESP8266-12E
  • Flash size: 4MBytes(32Bits)
  • Communication interface voltage: 3.3V.
  • Antenna type: Built-in PCB antenna is available.
  • Wireless 802.11 b/g/n standard
  • WiFi at 2.4GHz, support WPA / WPA2 security mode
  • Support STA/AP/STA + AP three operating modes
  • Built-in TCP/IP protocol stack to support multiple TCP Client connections (5 MAX)
  • D0 ~ D8, SD1 ~ SD3: used as GPIO, PWM, IIC, etc., port driver capability 15mA
  • AD0: 1 channel ADC
  • Power input: 4.5V ~ 9V (10VMAX), USB-powered
  • Current: continuous transmission: ≈70mA (200mA MAX), Standby: <200uA
  • Transfer rate: 110-460800bps
  • Support UART / GPIO data communication interface
  • Remote firmware upgrade (OTA)
  • Support Smart Link Smart Networking
  • Working temperature: -40 ℃ ~ + 125 ℃
  • Drive Type: Dual high-power H-bridge driver
  • ESP8266 has IO Pin
  • Don't need to download resetting
  • A great set of tools to develop ESP8266

Applications:

  • Home automation
  • Sensor networks

Package included:

  • 1x NodeMcu Lua WiFi Internet of Things Development Board Amica V2 Based on ESP8266-12E CP2102 Module

Comments

Post a Comment

Popular posts from this blog

nanoCH32V203 Dev Board

Image
These are all purchase variations of this page.  The chip is the new 10 cent RISC-V.  https://www.tindie.com/products/johnnywu/nanoch32v203-development-board/ https://www.tindie.com/products/johnnywu/wch-linke-debugger/ nanoCH32V203 Development Board WCH RISC-V Dual TYPE-C USB Interface LCD Interface SD Card Slot Open Source nanoCH32V203 is a development board made by MuseLab based on CH32V203C8T6 of QinHeng. It features dual TYPE-C USB interfaces, LCD interface and SD card slot on board, and can be programmed through the USB port which is convenient for prototype verification and development. Dual USB interface, USB1 supports Device, USB2 supports Host/Device Can be downloaded directly via USB without additional downloader Onboard 8MHz and 32.768K crystal oscillator FPC-12P cable connector, which can support common LCD (such as ili9341, st7789, etc.) SD card slot, which supports SD card reading and writing (SPI protoc ol) Kit 3: nanoCH32V203 Development Board x 1 + 20 Pin Header x 2 +
Read more

ESP-M3 Mini

Image
 https://www.aliexpress.us/item/2251832658774277.html Long-range Ultra-low Mini Ultra-Small ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266 ESP8285 = ESP8266 + 1M Flash, so that it can withstand high temperatures up to 125 degrees Celsius! And the original ESP8266 source code program can be used to transplant. ESP-M3 module core processor using cost-effective chip ESP8285. The chip integrates the enhanced version of the Tensilica's L106 Diamond 32-bit core processor with on-chip SRAM in a smaller package. ESP8285 has a complete Wi-Fi network function, both can be used independently, can also be used as a slave from other host MCU running. When the ESP8285 hosting application, can be started directly from the external Flash. Built-in cache memory facilitates system performance and optimizes storage systems. In addition, ESP8285 only through the SPI / SDIO interface or I2C / UART port can be used as a Wi-Fi adapter, applied to any microcontr
Read more