Posts

ICM-20948 Sensor Module 9 Axis MEMS

Image
  ICM-20948 Sensor Module 9 Axis MEMS   Lowest Power 9-Axis Device at 2.5 mW 3-Axis Gyroscope with Programmable FSR of ±250 dps, ±500 dps, ±1000 dps, and ±2000 dps 3-Axis Accelerometer with Programmable FSR of ±2g, ±4g, ±8g, and ±16g 3-Axis Compass with a wide range to ±4900 T Onboard Digital Motion Processor (DMP) Android support Auxiliary I2C interface for external sensors On-Chip 16-bit ADCs and Programmable Filters 7 MHz SPI or 400 kHz Fast Mode I⊃2;C Digital-output temperature sensor VDD operating range of 1.71V to 3.6V MEMS structure hermetically sealed and bonded at wafer level

2S LiIon board

Image
  TZT 2S 7.4V 8A Li-ion 18650 Lithium Battery Charger Protection Board 8.4V Overcurrent Overcharge / Overdischarge Protection
Image
  AS5600 magnetic encoder  https://ams.com/documents/20143/36005/AS5600_DS000365_5-00.pdf

TP5100 2A 4.2v/8.4v 1S/2S Lithium Battery Charger

Image
Sigh, copy the description and the internet thinks you're a spam site...  https://www.amazon.com/dp/B07S2RCT71?ref=ppx_pop_dt_b_asin_image&th=1 Description: TP5100 is a double switch buck 8.4V, single cell 4. 2V lithium battery charge management chip. Its ultra-compact QFN16 package and simple external circuit, making TP5100 ideal for portable equipment so large current charging management applications.Meanwhile, TP5100 built-in input overcurrent, undervoltage protection, over temperature protection, short circuit protection, battery temperature monitoring, reverse battery protection. TP5100 have 5V-18V wide input voltage, dual battery trickle charge into pre-charge, constant current, constant voltage three phase, pre-charge current trickle charge current through an external resistor adjustment, the maximum charge current up to 2A. TP5100 with a frequency of 400kHz switching mode makes it possible to use a smaller outer Suo device and the large current charging still maintain a

nanoCH32V203 Dev Board

Image
These are all purchase variations of this page.  The chip is the new 10 cent RISC-V.  https://www.tindie.com/products/johnnywu/nanoch32v203-development-board/ https://www.tindie.com/products/johnnywu/wch-linke-debugger/ nanoCH32V203 Development Board WCH RISC-V Dual TYPE-C USB Interface LCD Interface SD Card Slot Open Source nanoCH32V203 is a development board made by MuseLab based on CH32V203C8T6 of QinHeng. It features dual TYPE-C USB interfaces, LCD interface and SD card slot on board, and can be programmed through the USB port which is convenient for prototype verification and development. Dual USB interface, USB1 supports Device, USB2 supports Host/Device Can be downloaded directly via USB without additional downloader Onboard 8MHz and 32.768K crystal oscillator FPC-12P cable connector, which can support common LCD (such as ili9341, st7789, etc.) SD card slot, which supports SD card reading and writing (SPI protoc ol) Kit 3: nanoCH32V203 Development Board x 1 + 20 Pin Header x 2 +

ESP-M3 Mini

Image
 https://www.aliexpress.us/item/2251832658774277.html Long-range Ultra-low Mini Ultra-Small ESP-M3 From ESP8285 Serial Wireless WiFi Transmission Module Fully Compatible With ESP8266 ESP8285 = ESP8266 + 1M Flash, so that it can withstand high temperatures up to 125 degrees Celsius! And the original ESP8266 source code program can be used to transplant. ESP-M3 module core processor using cost-effective chip ESP8285. The chip integrates the enhanced version of the Tensilica's L106 Diamond 32-bit core processor with on-chip SRAM in a smaller package. ESP8285 has a complete Wi-Fi network function, both can be used independently, can also be used as a slave from other host MCU running. When the ESP8285 hosting application, can be started directly from the external Flash. Built-in cache memory facilitates system performance and optimizes storage systems. In addition, ESP8285 only through the SPI / SDIO interface or I2C / UART port can be used as a Wi-Fi adapter, applied to any microcontr

9 Key CNC Aluminum QMK Keyboard

https://www.amazon.com/dp/B09HXSRN8V https://github.com/the-via/releases/releases/tag/v1.3.1 https://docs.google.com/document/d/1BJcnhZ5vkn3fQsNT8oX1uHtpdYlxzqto7o9OaMJroPk/edit 9 Key CNC Aluminum QMK VIA Hotswap YMDK We set 5 as 5(Fn),when you long press 5,it is Fn,can control led color by Fn.If you want other keys or Macro keys,please program it yourself with the manuals below.When you tap 5 (Fn),it may feel little slower than other keys since it needs to decide to act as 5 or Fn. This QMK PCB is presoldered with Hot socket and RGB switch leds.If you are not familiar with QMK,we suggest you learn a little before ordering The switch we use is Gateron Pro Yellow which is POM stem and prelubed whose tactile feeling is much better than normal gateron yellow Gateron Pro Yellow is linear switches.Operating force is 50+-15gf.Total Journey is 4.0+0.4mm.Action stroke is 2+-0.6mm. When you replace switches in future,we suggest you use 3 pin SMD switches.If you want to use 5 pin switches,you ne